ALLPRO^® Corporation
  Brandon, FL 33511

AP4300 - 12181
November, 2001

An extremely durable, water borne modified acrylic enamel, which provides superior adhesion and abrasion resistance. For use on most interior and exterior surfaces where maximum, durability is desired. Excellent for use over new, properly prepared metal and most baked enamel surfaces. Contains a flash rust inhibitor allowing for direct to metal applications without the need of a primer coat.

• ASTM 3359 Cross Hatch Adhesion - 5
• ASTM D522 Flexibility (conical mandrel) ¼" - pass
• ASTM B117 Salt Fog Resistance - 150 Hours - No Effect
• Exterior Exposure - 45° South Florida - 6 months, Gloss Retention - 80° minimum

Steel, Galvanized Steel, Aluminum, Masonry, Concrete, Wood, Machinery, Plaster, Drywall, Properly Prepared Ferrous, and Nonferrous Metals.

Do not apply when temperature is below 50^°F or when rain is expected. Most high gloss enamels become slippery when wet. To ensure maximum safety on horizontal surfaces, a small amount of sand or pumice may be added to give coating nonskid characteristics. Not suitable for immersion service.

Surface must be clean, dry and free of rust, dirt, oil, grease, old loose paint, and other foreign matter.

STEEL AND GALVANIZED METAL should be clean and have a slight surface profile. An SSPC-SP-6 commercial blast is preferred for maximum performance. If this is not feasible, power or hand tool cleaning is acceptable. Product is self priming when 2 coats are applied. Maximum corrosion protection will be achieved through the use of a rust inhibitive primer, especially under darker colors. Pre-finished Siding [Baked on finishes] - 1 coat primer.
BARE WOOD should be sanded smooth. Prime with appropriate wood primer for best results.
NEW CURED OR UNPAINTED CONCRETE - acid etch, rinse thoroughly with clean water, and allow to dry before applying coating. Previously painted surfaces - glossy areas should be dulled by abrading the surface. If paint is peeling, or badly weathered, clean surface and proceed as for new surface.

Stir paint thoroughly before using. Apply with brush, roller or spray. Will cover most previously painted surfaces in one coat. Two coats will give surfaces better durability. Previously uncoated surfaces should be given two coats. Apply a full wet coat of 5.0 - 5.5 mils wet film thickness. 1.8 - 2.0 mils dry. No reduction is necessary. If thinning is necessary, use water. Do not add any more than ½ pint of water per gallon. Remove all splatters immediately.

Airless Spray settings @ 77º:
Tip Size: .015 - .019
Atomization Pressure: 1000-1500 psi

Clean up immediately after use with soap and water.

Contains solvents dispose of properly.

Caution

Technical Information

WARNING! IRRITANT! HARMFUL OR FATAL IF SWALLOWED.

Prolonged breathing of fumes and vapors may irritate respiratory tract causing headache, nausea and dizziness. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application an drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate properly fitted respirator (see Code of Federal Regulations 42 CFR 84) during and after application. Follow respirator manufacturer's directions for respirator use. Close container after each use. Do not get in eyes, on skin or on clothing. Wash thoroughly after handling.

If spilled, contain spilled material and remove with inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

WARNING: This product contains a chemical known to the state of California to cause cancer and birth defects or other reproductive harm.

FIRST AID: in case of contact with eyes, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention immediately. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. If swallowed, do not induce vomiting. Call physician immediately. In case of medical emergency, contact 1-800-424-9300.

Obtain And Read The Material Safety Data Sheet Before Using.

INTENDED FOR INDUSTRIAL USE ONLY.

Manufactured For:
ALLPRO^® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.