GuardPro Guard Pro Industrial Spray

Description	ALLPRO^® GUARDPRO^® High Solids Industrial Spray Primers are high performance coatings specifically formulated for use with ALLPRO GUARDRO High Solids Industrial Spray Enamels to provide maximum performance under severe weather conditions or chemical exposure. Ideal for maintenance, repair and general surface protection.
Prominent Features	» Fast drying » Protects against rust, oil, gasoline & most corrosive chemicals » Interior & exterior use » Resists abrasion, heat & humidity » Tamper-proof cap » Full length draw tube ensures maximum delivery per can » Internal heavy-disc mixer for faster, more thorough paint mixing
Uses	Excellent for most types of wood and metal items such as blowers, benches, machinery, racks, fire doors, sprinkler systems, bins, motors, tanks & piping. For maximum protection topcoat with ALLPRO GUARDPRO Industrial Spray Enamel
Limitations	Galvanized surfaces should be primed prior to application with a galvanized primer.
Surface Preparation	Clean surface thoroughly, removing all dirt, grease, oil, soapy film, loose rust, moisture, etc. and cover adjacent areas to protect from spray mist. For maximum protection on metal substrates, remove all rust and prime bare surfaces.
Application	Use in well ventilated area. Shake can vigorously for one minute before spraying and occasionally while in use. Hold can 8 - 10 inches from surface to be sprayed. Spray at room temperatures between 70ºF - 90ºF (21 - 32ºC). For best results, apply thin even coats – two thin coats are better than one heavy one. Recoat after 2 hours. If nozzle clogs during use, turn spray button ¼ turn or remove and clean button slot. Do not stick objects into can opening.
Clean Up	Clean overspray immediately after use with paint thinner. For storage, clear nozzle immediately after use by holding can upside down, spraying 2-3 seconds or until paint no longer sprays out of can.
Environmental Concerns	Compliant with all U.S. VOC regulations for aerosol paint. Contains no methylene chloride or any ozone damaging fluorocarbons.

Caution

Technical Information

DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR. VAPORS MAY CAUSE FLASH FIRE. CONTENTS UNDER PRESSURE.

VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION. Do not puncture or incinerate (burn) container. Exposure to heat or prolonged exposure to sun may cause bursting. Do not expose to heat or store at temperatures above 120ºF (49ºC).

Notice: Reports have associated repeated and prolonged occupational over exposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling contents may be harmful or fatal.

Vapors may ignite explosively. Keep away from heat, sparks and flame. Do not smoke. Extinguish all flames and pilot lights, turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation.

Use only with adequate ventilation. Do not breathe dust, vapors or spray mist. Open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory equipment protection (NIOSH/MSHA approved) or leave the area. Close container after each use. Avoid contact with eyes, skin and clothing.

First Aid: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced get medical attention immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

KEEP OUT OF REACH OF CHILDREN
Obtain And Read The Material Safety Data Sheet Before Using

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: 20 fl. oz. aerosol can – 17 oz. by wt. (482g)
Colors: Red Iron Oxide Primer and Light Gray Primer
Weight Per Gallon: n.a.
Specific Gravity: Varies by color. 0.77 - 0.90
Solids by Volume: n.a.
% Solids by Weight: varies by color. Approximately 33%.
Viscosity: n.a.
Spreading Rate: Approx. 25 sq. ft. per can @ 1 mil dry film thickness
Gloss (60º angular): 15 maximum
Heat Resistance: 300ºF (149ºC)
Shelf Life: 2 years
Freeze Thaw: n.a.
Dry Time -
     Dry-to-touch: 5-7 minutes
     Tack-free: 15 minutes
     Dry hard: 48 hours
     Recoat: After 2 hours
Flash Point: -4ºF (-20ºC)
Odor: Strong odor
Storage: Indoors. Do not expose to heat or store
     at temperatures above 120ºF. Exposure to heat
     or prolonged exposure to sun may cause
     bursting. Do not puncture or incinerate container
Vehicle: Phenolic polymer
Air Quality Data: Contains no methylene chloride or
     any ozone damaging fluorocarbons. VOCs vary
     by color. Less than 60%

		Technical Bulletin

		GUARDPRO^® H.S. Industrial Spray Primer