All Seal Waterproofing Sealer

Description	ALLPRO^® All-Seal™ Waterproofing Sealer is an alkali and U.V. resistant non-flammable, non-yellowing, waterborne sealer designed for use on above-grade concrete, masonry, and wood surfaces. It is a clear drying, environmentally friendly, fast drying water repellent based on state of the art Acryl-Hydrophobe copolymer technology. All Seal contains 50% more solids by weight than the leading competitor, giving it enhanced durability and greater water repellent properties. When dry, All Seal provides a rich, semi-gloss finish to the substrate. Easy-to-use water clean-up formula.
Prominent Features	» Highly Penetrating » Water Clean-up » Water Repellent » Easy Application » U.V. Resistant » Alkali Resistant
Uses	Ideal for use as a water repellent on concrete, masonry, stucco, brick, stone, adobe, drywall, plaster, roof tiles, grout, pottery, galvanized metal, vinyl siding, spruce, redwood, cedar (siding and shake shingles), plywood, pressed board, wafer board, wood decks (pressure treated), and more. All Seal can also be used as a masonry conditioner for binding moderately chalk-laden surfaces prior to final coating with top quality exterior latex house paint or elastomeric coating. By sealing the substrate surface, All Seal increases the overall waterproofing performance of topcoats, as well as extending top coat coverage - a cost saving advantage.
Limitations	Do not use on wood that has been recently surface treated with insecticides and/or chemical preservative compounds that prevent dry rot. Do not apply when temperature of surface or air is below 50 degrees F (10 degrees C). If rain or threatening weather is expected within 8 hours, delay application until dry conditions. Never apply to frozen or frost covered substrates. Do not apply product to wet or water saturated substrates or when relative humidity is above 90%. Not for use below grade or under water. Do not use on traffic-bearing surfaces. KEEP FROM FREEZING.
Surface Preparation	The most important factor in achieving a durable, quality finish is proper surface preparation. The substrate must be free from all surface contamination such as dirt, dust, laitance, mold, mildew, mortar, mill scale, loose paint, surface efflorescence, grease, oil, excessive chalk, and foreign matter. The removal of grease, oil, and dirt is best achieved by pressure cleaning while utilizing commercial degreasers. Neutralize chemical cleaners, and complete tuck-pointing, crack and delamination (spalling) repairs prior to the application of All Seal. Remove previous coatings by mechanical means (Caution: read all warning statements pertaining to dust masks, etc.). Do not apply over coated surfaces without testing for compatibility and adhesion. Efflorescence is best removed by scraping and wire brushing the surface. Dust, dirt and chalk are best removed by high-pressure water blasting. To determine if the chalk has been sufficiently removed, wipe hand over the dried surface; if a powdery colored residue is still visually evident on the hand, then more high-pressure water blasting is required to remove this chalky layer to a practical bare minimum. Removal of laitance and any other under bound chalk-like matter is best achieved by etching the surface with a dilute solution of Muriatic acid; i.e., 4 parts water to 1 part Muriatic acid. Note: Always be sure to read all manufacturers' instructions pertinent to degreasers and Muriatic acid solutions prior to use.
Application	Apply when temperature of surface and air is above 50 degrees F (10 degrees C). All Seal is alkali resistant, and can be applied to masonry surfaces 3-7 days after construction (PH must 11 or less). Cementitious Surfaces: All Seal is ready for use. Do not thin. Apply All Seal to a clean, dry surface by roller, HVLP (high volume low pressure spray system), or airless spray system. For maximum effectiveness, two (2) coats should be applied, allowing four hours between applications. Areas not being coated, such as windows and shrubbery, should be protected from overspray. All Seal may be mixed in a 1-1 ratio with acrylic paint to produce a pigmented primer/sealer. To improve the weatherability of latex paints, add All Seal in a 1-20 ratio (approx. one quart All Seal per 5 gal. latex paint). Wood: Due to its water repellent properties and built-in U.V. resistance, All Seal protects wood from the premature damaging effects of repetitious water absorption while allowing the wood to age naturally. All Seal can be applied to most above-grade wood building construction. Follow above directions. Do not use on wood that has been recently surface treated with insecticides and/or chemical preservative compounds that prevent dry rot.
Clean Up	Clean equipment with soap and water.

Caution

Technical Information

WARNING! HARMFUL IF SWALLOWED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE, AND NAUSEA. MAY BE HARMFUL IF ABSORBED THROUGH SKIN. CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. CONTAINS: 2-(2-METHOXYETHOXY) ETHANOL. DO NOT TAKE INTERNALLY. IN CASE OF INGESTION, CALL PHYSICIAN IMMEDIATELY. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN.

NOTICE: This product contains solvents. reports have associated repeated and prolonged occupational exposure to solvents with permanent brain damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. For emergency information within the United States, call (800)424-9300; outside the U.S. call (703)527-3887 [CHEMTREC]. For additional safety and chronic hazard information, refer to Material Safety Data Sheet for this product. See label analysis for list of primary ingredients. Close container after each use. If sanding is done, wear dust mask to avoid breathing of sanding dust. IMPORTANT! Spray equipment must be operated with care and in strict accordance with manufacturer's instructions. Avoid breathing vapor, spray mist or sanding dust. Wear an appropriate, properly fitted respirator (NIOSH/MSHA approved) during and after application unless air monitoring demonstrates vapor/mist labels are below applicable limits. Follow respirator manufacturer's directions for respirator use. FIRST AID: In case of skin contact, wash off quickly with plenty of water, then soap and water; remove contaminated clothing. For eye contact flush immediately with large amounts of water, especially under lids, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. Restore and support continued breathing. Have trained person give oxygen if necessary. If discomfort persists or any breathing difficulty occurs, get medical help. In case of spillage, absorb with inert material and dispose of in accordance with applicable regulations.

Material Safety Data Sheets (MSDS) available upon request. Similar information for solvents and other chemicals used with ALLPRO products should be obtained from you supplier(s). When solvents are used, proper safety precautions must be observed.

KEEP FROM FREEZING.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: "F" style plastic gallon and "Tite-head" five (5)
     gallon pails.
Color: When wet - Milky White
     When dry - Clear
Finish: Semi-Gloss
Weight per Gallon: 8.5 ± 0.2 lbs.
% Solids by Weight: 15.0% =/- 0.5%
% Solids by Volume: 14.3% minimum
Coverage: 100-250 sq. ft. per gallon (It is
     recommended that a test in a small,
     inconspicuous area be conducted first to
     determine the total gallonage required for the job)
pH (when packaged): 9.2 ± 0.2
Viscosity:23 seconds Zahn #1 cup
Rheological Characteristics: Newtonian - thin
     consistency
Dry Time at 75°F & 40% R.H.
     To Touch: 1 hour
     To Recoat: Approximately 4 - 6 hours
     (temperature & humidity dependent)
Service temp. range: -20°F to 160°F
Flash Point: Non-flammable, waterborne
Odor: Very low, ammonia-like
Storage: Inside, between 32°F & 100°F (0°C & 38°C)
Shelf Life: 2 years minimum
Freeze/Thaw (ASTM C731): Do not freeze
Film Formation Temperature: 40°F - 125°F
Water Blush Resistance (Black Tile): None - after 6
     hour spot test
Alkali Resistance: Up to pH 11
Post Yellowing after 250 Hours (Tomb Stone):
     Essentially none
Efflorescence Preventiveness: Excellent
Contact Angle (Water Bead): More surface sheeting
     than bead repelling.
U.V. Absorber: Proprietary Benzotriazole Structure
Light Stabilizer: Bis (1,2,2,6,6 - pentamethyl -4-
     piperrididinyl) Sebacate
Vehicle: Acryl-Hydrophobe Copolymer
Volatile Portion (Exempt): Water
Volatile Portion (Non-Exempt): 2 - (2-Methoxyethoxy)
     Ethanol
Air Quality Data: VOC content 107 g/l (0.8917 lb./gal.)

Analysis CAS:
Acryl-Hydrophobe Copolymer - CAS unknown
2-(2-Methoxyethoxy) Ethanol          111-77-3
Proprietary Benzotriazole Structure 104810-47-1
Bis (1,2,2,6,6 - pentamethyl -4-
     piperrididinyl) Sebacate             41556-26-7
Additives                                       (Proprietary)
Water                                           7732-18-5
Contents partially unknown

		Technical Bulletin

		All-Seal Waterproofing Sealer