Technical Bulletin
Kitchen & Bath Adhesive
|
|
Technical Bulletin |
|
|
Kitchen & Bath Adhesive |
||
|
ALLPRO®
Corporation |
AP6750 - 60361 |
| Description | Kitchen &
Bath wallcovering adhesive is a synthetic polymer-based adhesive
designed specifically for use in high humidity areas, such as kitchens
and bath rooms. It can be used on pre-pasted and unpasted wallcoverings.
|
| Prominent Features |
|
| Uses | Recommended for
light and medium-weight wallcoverings. Strippable when used with woven,
fabric-backed vinyl wallcoverings when applied over ALLPRO®
ULTRA•PREP™ primer.
|
| Limitations | Not recommended
for direct application over oil/alkyd primers. Keep from freezing.
|
| Surface Preparation | Existing
wallpaper must be removed. Surface must be clean, dry and free from
dirt, dust, grease, oil, mildew, wax or loose paint. Check surfaces for
paint bonding, damaged wallboard or plaster by cutting a small X with a
sharp knife and attempt removal with a small piece of "Scotch"
tape. Repair all unsound surfaces. Remove existing mildew by applying a
solution of 1 cup of bleach to 2.5 gallons of water, then rinse clean.
Prime all surfaces (including oil-based coatings) with ALLPRO®
ULTRA•PREP™ acrylic primer. Before proceeding with any unusual
conditions, consult your adhesive or wallcovering supplier.
|
| Application | Use only when the
adhesive, wallcovering and surface temperatures are above 50ºF (10ºC).
When using with pre-pasted wallcoverings, thin with eight (8) ounces of
water per gallon prior to application. Use full-bodied when using
un-pasted wallcoverings. Apply a thin, uniform coat of adhesive with a
brush or roller to one sheet at a time. Avoid contact with the surface
of embossed, textured or delicate wallcoverings. Note: Kitchen &
Bath Adhesive takes one week to cure before it attains its properties.
Book according to the wallcovering manufacturer’s instructions. Do not
overbook.
|
| Clean Up | Clean all
equipment and wallcovering surfaces immediately after use with warm,
clean water with frequent changes of water. Additional effort may be
required if the adhesive is allowed to contact the surface of embossed
or textured vinyls.
|
| Disposal | Kitchen &
Bath Adhesive is water-based and does not contain organic solvents.
Place empty containers in normal refuse for disposal. Contact
your local sanitation department or household hazardous waste
coordinator for information concerning possible reuse or disposal of
unused water-based paints, primers or adhesives.
|
| Limited Warranty | If,
within 24 months of manufacture and used as directed, this product is
found defective in material or workmanship, it will be replaced without
charge upon presentation of proof of purchase and this used container.
This warranty is in lieu of any other, the exclusive remedy is limited
to replacement of product and ALLPRO disclaims all liability for
consequential damages. Conditions of use are beyond our control.
|
|
Caution |
Technical Information |
| Do
not freeze. Do not take internally. In case of ingestion, seek medical
attention. Avoid contact with skin and eyes. Use of skin and eye
protection is recommended at all times. If contact with eyes occurs,
flush with water for 15 minutes. If skin contact occurs, wash with soap
and water. Seek medical attention if rash or other symptoms occur. Do
not mix with other chemicals. Use in a well ventilated work area. Close
container after each use. Keep out of reach of children.
Manufactured For: |
Packaging:
Vinyl tubs Color: White Weight per Gallon: Approx. 8.60 lbs. % Solids by Weight: Approx. 18% Viscosity: Approx. 25,000 cps Spreading Rate: Approx. 250 sq. ft. per gal. Shelf Life: 1 year minimum Freeze Thaw: Do not freeze Dry Time: Varies depending on temperature, ventilation and humidity of the room. Flash Point: Nonflammable Odor: Very low Storage: Avoid freezing; keep in cool, dry place Vehicle: Synthetic polymer Air Quality Data: VOC (calculated) <50 g/l Analysis:
|