Tub & Tile Adhesive Caullk Tub 'N Tile

Description	Tub and Tile Adhesive Caulk is made from a special formulation of elastomeric latex copolymer, combined with silicone and other selected ingredients. It is bright white in color. It is easy to apply, dries quickly, will seal up to 1/2" wide openings and may be painted when dry.
Prominent Features	» Multi-purpose adhesive caulk » Mildew resistant » Excellent adhesive qualities » Brilliant white » Vacuumized to ensure maximum durability
Uses	For use on land and sea. Particularly useful for sealing around tubs, wash stands, showers, doors, windows, fixtures and for sealing loose tiles and replacing grout.
Limitations	Not recommended for use underwater. Keep from freezing. Allow to dry thoroughly, usually 24 hours, before exposing to water.
Surface Preparation	Surfaces must be firm, dry and free of soap film, mildew, dirt, oil, grease, wax, loose paint and old caulking material. Rubbing alcohol works well to prepare tile, porcelain and other surfaces. Household bleach will remove mildew. Caulk and substrate should be at least 50° F for best application and cure.
Application	Remove tip and trim nozzle to desired bead size. Apply evenly, (for best application control, bend end of tube back over tube to apply caulk). Smooth bead gently with wet finger and wipe excess with a damp cloth. A 5.5 fluid ounce squeeze tube should be enough for two regular tubs. Material is tack free in 30 minutes. Allow to dry at least 24 hours before water exposure.
Clean Up	Clean up with water immediately after use and before bead is cured on surface.
Disposal	Contains organic solvents which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your local sanitation department or household hazardous waste coordinator for information concerning possible reuse or disposal of unused solvent-containing adhesives and/or sealants.
Limited Warranty	If, when applied as directed, this material peels, cracks or separates, it will be replaced without charge upon presentation of proof of purchase and used cartridge. This limited warranty only applies to residential use and damages including consequential damage and other remedies are excluded. No other warranties apply, including fitness for particular purpose.

Caution

Technical Information

Do not take internally

WARNING! CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN.

NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For emergency information call (800) 228-5537. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use.

FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help.

Material Safety Data Sheets (MSDS) available upon request. Similar information for solvents and other chemicals used with ALLPRO products should be obtained from you supplier(s). When solvents are used, proper safety precautions must be observed.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: 5.5 fluid ounce squeeze tube
Color: White
Weight per Gallon: 11.5 ± 0.2 lbs.
Specific Gravity: 1.39
% Solids by Weight: 73.2% ± 1%
% Solids by Volume: 73.3% ± 1%
pH (when packaged): 9.3 ± 0.2
Viscosity: Smooth thixotropic paste
Dry Time at 73°F & 40% R.H.
     Tack Free: 1/2 hour
     Dry Hard: Allow 24 hours before water exposure.
     Approximately 3-4 days for full cure.
Service temp. range: 10°F to 150°F (12°C to 65°C)
Hardness (Shore A Durometer, ASTM D2240): 61 ± 5
Slump (ASTM D2202): Zero
Flash Point: Nonflammable, waterborne
Odor: Low - banana like
Storage: Inside, between 32°F & 100°F (0°C & 38°C)
Shelf Life: 2 years minimum
Freeze/Thaw (ASTM C731): Passes 5 cycles
Vehicle: Vinyl Acetate complex resin
Volatile Portion (Exempt): Water
Volatile Portion (Non-Exempt): Ethylene Glycol /
     Glycol Ester
Air Quality Data: VOC 29 g/l (0.24 lb./gal.)

Analysis:
Vinyl Acetate Resin (CAS unknown)
Butyl Benzyl Phthalate (85-68-7)
Glycol Ester (628-63-7)
Calcium Carbonate (471-34-1)
Ethylene Glycol (107-21-1)
Contents Partially Unknown
Water (7732-18-5)

		Technical Bulletin

		Tub & Tile Adhesive