Technical Bulletin
Spackling Paste
|
|
Technical Bulletin |
|
|
Spackling Paste |
||
|
ALLPRO®
Corporation |
AP4950 - 16427 |
| Description | ALLPRO
Spackling Paste is a ready-mixed spackle, that is easy to use for
filling holes and cracks in interior walls, ceilings and woodwork. It is
easy to apply and tool with minimal shrinkage. It is white in color and
will not crumble, flake or discolor. Meets Federal Specification
SS-P-00450 Type II.
|
| Prominent Features | »
Bright white » Minimal shrinkage » East to tool - "Hangs" on a knife » Soap & water clean up » Fast one step repair
|
| Uses | Use
for filling holes and cracks in interior walls, ceilings and woodwork.
|
| Limitations | Not
suitable for exterior use. Keep from freezing.
|
| Surface Preparation | Surface
must be clean, dry and free from dirt, dust, grease, oil, mildew, wax
and loose paint. New or unpainted porous surfaces should be primed and
allowed to dry prior to patching.
|
| Application | Apply
with a flexible putty knife or broad knife and press firmly into open
space. Larger holes and cracks may require more than one application.
Apply only when spackling paste and surface temperatures are above 50°
F (10° C). Allow patch to dry for one hour between application.
|
| Clean Up | Clean
up with soap and water.
|
| Disposal | Unused
paste can contain trace quantities of vinyl acetate monomers which may
cause adverse effects to the environment if disposed of improperly.
Place empty containers in normal refuse for disposal. Contact
your local sanitation department or household hazardous waste
coordinator for information concerning the correct procedure for
disposal of containers which still contain unused material.
|
| Limited Warranty | This
product is warranted to perform satisfactorily when used in accordance
with the directions. Liability shall be limited to the replacement of
the material or refund the purchase price and does not include labor or
consequential damage. No other warranties apply, including fitness for
particular purpose.
|
|
Caution |
Technical Information |
|
Dry or mechanical sanding of this product
after use may result in the generation of nuisance dust. When dry
sanding the use of a dust/particulate respirator approved by NIOSH/MSHA
should be worn. MAY IRRITATE EYES. AVOID EYE CONTACT. USE ONLY WITH
ADEQUATE VENTILATION. Do not take internally. KEEP OUT OF REACH OF
CHILDREN.
NOTICE: This product contains trace chemicals known to the state of California to cause cancer. For emergency information call (800) 228-5537. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. Manufactured For: |
Packaging: Standard vinyl tub packaging - 4 gallons per case 6 quarts per case 24 1/2 pints per case Color: White Weight per Gallon: 15.45 ± 0.2 lbs. Specific Gravity: 1.87. % Solids by Weight: 78.0% ± 1% % Solids by Volume: 59.5% ± 1% pH (when packaged): 8.3 ± 0.2 Viscosity: Smooth thixotropic paste 425,000 ± 25,000 centipoise Dry Time at 73°F & 40% R.H. Tack Free: 1 hour Dry Hard: Approximately 4 - 6 hours. Paintable with oil or latex/acrylic when dry. Service temp. range: -5°F to 180°F (-23°C to 82°C) Flash Point: Nonflammable, waterborne Odor: Very low Storage: Inside, between 32°F & 100°F (0°C & 38°C) Shelf Life: 2 years minimum Freeze/Thaw (ASTM C731): Passes 5 cycles Vehicle: Vinyl Acetate Polymer Volatile Portion (Exempt): Water Volatile Portion (Non-exempt): Polyethylene Glycol Air Quality Data: VOC 25.5 g/l (0.25 lb./gal.) Analysis: |