Lite Patch Lightweight Spackling Compound

Description	Lite Patch™ Lightweight Spackling Compound is a smooth, pre-mixed waterborne product which contains no asbestos. It is scientifically formulated not to crack or shrink, even when used to repair large holes or dents, and is specifically designed for use on wood, plaster, sheetrock, stucco and masonry.
Prominent Features	» Water based » Fast drying » Will not shrink or crack » Does not contain asbestos » Specifically designed for use on wood, plaster, sheetrock, stucco and masonry
Uses	For use on wood, plaster, sheetrock, stucco and masonry.
Limitations	Not suitable for use on metal or plastic. Keep from freezing
Surface Preparation	Surfaces must be dry, clean and free of dust, dirt and old paint. New or unpainted porous surfaces should be primed and allowed to dry before patching.
Application	Stir well before use. Apply only when spackling compound and surface temperatures are above 50ºF (10ºC). If thinning is required, use up to one teaspoon of water per 1/2 pint of compound. Mix well. Apply with a broad knife and force into opening. Dries quickly. May be sanded with fine or medium sandpaper or sanding block. May be painted with oil or water based paints when dry.
Clean Up	Cleanup with warm, soapy water after use.
Disposal	Unused paste can contain trace quantities of vinyl acetate monomers which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your local sanitation department or household hazardous waste coordinator for information concerning the correct procedure for disposal of containers which still contain unused material.
Limited Warranty	This product is warranted to perform satisfactorily when used in accordance with the directions. Liability shall be limited to the replacement of the product material or refund of the purchase price and does not include labor or consequential damage. This limited warranty only applies to residential use. No other warranties apply, including fitness for particular purpose.

Caution

Technical Information

Dry or mechanical sanding of this product after use may result in the generation of nuisance dust. When dry sanding the use of a dust/particulate respirator approved by NIOSH/MSHA should be worn. MAY IRRITATE EYES. AVOID EYE CONTACT. USE ONLY WITH ADEQUATE VENTILATION. Do not take internally. KEEP OUT OF REACH OF CHILDREN.

NOTICE: This product contains trace chemicals known to the state of California to cause cancer. For emergency information call (800) 228-5537. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: Standard vinyl tub packaging -
     4 gallons per case
     6 quarts per case
     24 1/2 pints per case
Color: White
Weight per Gallon: 4.25 ± 0.2 lbs.
Specific Gravity: 0.51.
% Solids by Weight: 39.5% ± 1%
% Solids by Volume: 69.0% ± 1%
pH (when packaged): 8.0 ± 0.2
Viscosity: Smooth thixotropic paste 75,000 ± 5,000
     centipoise
Spreading Rate: Approximately 50 linear feet
     @ bead of 1/8" x 1/4"
Dry Time at 73°F & 40% R.H.
     Tack Free: 1 hour
     Dry Hard: Approximately 4 - 6 hours. Paintable
     with oil or latex/acrylic when dry.
Service temp. range: -5°F to 180°F (-23°C to 82°C)
Flash Point: Nonflammable, waterborne
Odor: Very low
Storage: Inside, between 32°F & 100°F (0°C & 38°C)
Shelf Life: 2 years minimum
Freeze/Thaw (ASTM C731): Passes 5 cycles
Vehicle: Vinyl Acetate Polymer
Volatile Portion (Exempt): Water
Air Quality Data: VOC 0 g/l (0.0 lb./gal.)

Analysis:
Vinyl Acetate Resin (CAS unknown)
Borosilicate Glass (65997-17-3)
Contents Partially Unknown
Water (7732-18-5)

		Technical Bulletin

		Lite Patch™ Lightweight Spackling