Technical Bulletin
Glazing Compound
|
|
Technical Bulletin |
|
|
Glazing Compound |
||
|
ALLPRO®
Corporation |
AP4950 - 16462 |
| Description | ALLPRO
Glazing Compound is a top quality, 100% oil-based, ready-to-use glazing
compound. After application it forms a tough elastic seal which is
weather proof and sag resistant. ALLPRO Glazing Compound is ideal for
both wood and metal window frames. It has excellent handling
characteristics, knives quite easily and is paintable.
|
| Prominent Features | »
Meets consumer spec. C-669-75 and Federal
spec. TT-G-410E. » Top quality, all purpose glazing compound » Forms a tough, elastic seal » Weather resistant and non sag » Non-asbestos » Easily tooled » Paintable » Works equally well as a painter’s putty
|
| Uses | Ideal
for bedding and setting glass panes into all metal or wood sash on new
construction or retrofit of existing windows. Additional uses include,
fill voids, cracks, and imperfections in walls, and will adhere to wood,
metal, drywall, plaster and many other common building surfaces.
|
| Limitations | Keep
from freezing.
|
| Surface Preparation | Surface
must be clean, dry and free from dirt, dust, grease, oil, mildew, wax
and loose paint. When re-glazing, remove all old paint and
putty/glazing. Prime any remaining paint or putty prior to application.
|
| Application | Glazing
Compound should be applied at temperatures above 40°F, to clean, dry
surfaces. Apply a thin layer or "bed" of glazing at angle with
putty knife or similar tool. For best results the glazing should be
painted with a high quality oil-base or latex/acrylic paint after
surface has fully skinned. Can be painted within 7 days with latex based
paint. When using to fill voids, cracks and imperfections, follow same
application procedures as above; allow glazing to fully skin before
painting.
|
| Clean Up | Cleanup
immediately after use with mineral spirits. Remove smears with mineral
spirits before dried. Product may be scraped away with razor after
dried. Because of the never harden formulation, removal represents very
little trouble.
|
| Disposal | Unused
material can contain trace quantities of ketoxime based chemical
compounds which may cause adverse effects to the environment if disposed
of improperly. Place empty containers in normal refuse for
disposal. Contact your local sanitation department or household
hazardous waste coordinator for information concerning possible reuse or
disposal of unused solvent-containing adhesives and/or sealants.
|
| Limited Warranty | This
product is warranted to perform satisfactorily when used in accordance
with the directions. This limited warranty only applies to residential
use and damages including consequential damage and other remedies are
excluded. Liability shall be limited to the replacement of the material
or refund the purchase price. No other warranties apply, including
fitness for particular purpose.
|
|
Caution |
Technical Information |
|
Dry or mechanical sanding of this product
after use may result in the generation of nuisance dust. When dry
sanding the use of a dust/particulate respirator approved by NIOSH/MSHA
should be worn. MAY IRRITATE EYES. AVOID EYE CONTACT. USE ONLY WITH
ADEQUATE VENTILATION. Do not take internally. KEEP OUT OF REACH OF
CHILDREN.
NOTICE: This product contains extremely small, but detectable chemicals known to the state of California to cause cancer. For emergency information call (800) 228-5537. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use to retain residues and avoid unwanted skinning. Practice good PERSONAL HYGIENE after using this material, especially before eating, drinking smoking, using the toilet or applying cosmetics. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. Manufactured For: |
Packaging: Standard metal container 4 gallons per case 6 quarts per case 24 1/2 pints per case Color: White Weight per Gallon: 16.0 ± 0.5 lbs. Specific Gravity: >1.0 % Solids by Weight: 98% - 99% % Solids by Volume: 98% - 99% Viscosity: Smooth heavy body paste Spreading Rate: Approximately 325 linear feet @ bead of 1/8" x 1/4" Dry Time: Usually skins over in 16-24 hours. Paintable with latex/acrylic after 6-7 days of drying. Service temp. range: -30°F to 180°F (-34°C to 82°C) Flash Point: > 220°F Odor: Very low Storage: Inside, between 32°F & 100°F (0°C & 38°C) Shelf Life: 1 year minimum Vehicle: Blend of Soya & Mineral Oils Air Quality Data: VOC compliant Analysis: |