Easy Gun AC Easy Gun A.C.

Description	Easy Gun AC™ Acrylic Latex plus Silicone is specially formulated for arid climates. Easy Gun AC is an all purpose sealant for interior and exterior use with a 35 year life span. It has excellent adhesion to most common building materials. Can be applied to wood, metal, concrete, brick, plaster, masonry, dry-wall, glass and ceramic tile.
Prominent Features	» Excellent Adhesion » Mildew resistant. » Meets ASTM C-834, Type P, Grade -18ºC. • Tough, durable and pliable » Silicone fluids are added to help seal out moisture & air, plus improve adhesion & water resistance. » Non-bleeding » Vacuumized - microscopic air has been removed to eliminate pops and spurts during application to assure a smooth, even, non-porous bead.
Uses	Ideal for sealing cracks, seams and joints around windows, doors, woodwork, siding, flashing, air conditioners and bathroom and kitchen counters.
Limitations	Not intended for under water use. Do not apply when rain is expected. Keep from freezing. Not for use on food contact areas.
Surface Preparation	Surface must be clean, dry and free from dirt, dust, grease, oil, mildew, wax, loose paint and old caulking material. Prime bare surfaces before caulking.
Application	Apply only when sealant and surface temperatures are above 50ºF (10ºC). Cut nozzle at a 45º angle to desired thickness of bead. Apply with a standard or dripless caulking gun. Use steady pressure to completely fill joints. For a neat appearance, smooth bead with a moistened brush or cloth. Remove excess material before cured using a water moistened cloth. For best results, cured beads should be between 1/8" - 1/2" wide and 1/8" - 1/4" deep. Use backing rod for cracks deeper than 1/4".
Clean Up	Clean all equipment immediately after use with warm, soapy water
Disposal	Contains organic solvents which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your local sanitation department or household hazardous waste coordinator for information concerning possible reuse or disposal of unused solvent-containing adhesives and/or sealants.
Limited Warranty	If, when applied as directed, this material peels, cracks or separates within 35 years after application, it will be replaced without charge upon presentation of proof of purchase and used cartridge. This limited warranty only applies to residential use and damages including consequential damage and other remedies are excluded. No other warranties apply, including fitness for particular purpose.

Caution

Technical Information

Do not take internally.

WARNING! CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN.

NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For emergency information call (800) 228-5537. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use.

FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help.

Material Safety Data Sheets (MSDS) available upon request. Similar information for solvents and other chemicals used with ALLPRO products should be obtained from you supplier(s). When solvents are used, proper safety precautions must be observed.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: Standard packaging - 10.1* fluid ounce plastic cartridges. ( * Packaging in mid-late 2002 changing from 10.5 fl. oz. to 10.1 fl. oz. fill)
Color: White
Weight per Gallon: 13.5 ± 0.2 lbs.
Specific Gravity: 1.62
% Solids by Weight: 82% ± 1%
% Solids by Volume: 70% ± 1%
pH (when packaged): 8.1 ± 0.2
Viscosity: Smooth thixotropic paste
Extrudability (ASTM C731): 2 g/s, minimum
Spreading Rate: Approximately 48 linear feet @ bead of 1/8" x 1/4"
Dry Time -
Tack Free: 1 hour at 73°F & 40% R.H.
Dry Hard: Approximately 4 - 6 hours. Paintable with oil or latex/acrylic when dry.
Service temp. range: -30°F to 180°F (-34°C to 82°C)
Flexibility (1/4" slab on aluminum @ -15°F, ASTM C734): Pass
Hardness (Shore A Durometer, ASTM D2240): 55
Slump (ASTM D2202): Zero
Flash Point: Nonflammable, waterborne
Odor: Very low
Storage: Inside, between 32°F & 100°F (0°C & 38°C)
Shelf Life: 2 years minimum
Freeze/Thaw (ASTM C731): Passes 5 cycles
Vehicle: Siliconized Acrylic Polymer
Volatile Portion (Exempt): Water
Volatile Portion (Non-Exempt): Ethylene Glycol / Petroleum Spirits
Air Quality Data: VOC 72.8 g/l (0.68 lb./gal.)

Analysis:
Acrylic Terpolymer Resin (CAS unknown)
Butyl Benzyl Phthalate (85-68-7)
Petroleum Distillate (8052-41-3)
Calcium Carbonate (471-34-1)
Ethylene Glycol (107-21-1)
Formaldehyde (50-00-0)
Contents Partially Unknown
Water (7732-18-5)

		Technical Bulletin

		Easy-Gun™ AC