ALLPRO^® Corporation
  Brandon, FL 33511

AP4300 - 12055
November, 2001

Ready to spray, high gloss line of enamels that dry in 15 minutes. Excellent resistance to fungus, salt air and alkalis. Suitable for interior and exterior applications. Recoatable in 2 hours.

• ASTM D1308 Chemical Resistance
  2% Sodium Hydroxide - No Effect
  5% Acetic Acid - No Effect
  Lactic Acid - No Effect
  Mineral Oil - No Effect
• ASTM B117 Salt Fog Resistance - 200 Hours - No Effect
• ASTM D522 Elongation (conical mandrel) 1/8" pass
• Dry Heat Resistance - 200°F continuous, 250°F intermittent
  

Lawn Furniture, Machinery, Ornamental Iron, Farm Equipment, Factory Equipment.

Do not apply when temperature is below 50^°F or when rain is expected. Most high gloss enamels become slippery when wet. To ensure maximum safety on horizontal surfaces, a small amount of sand or pumice may be added to give coating nonskid characteristics. Recommended for spray application, although small areas may be brushed. Not for immersion. Not recommended for floors or for extreme chemical environments. Will yellow under some conditions, especially in interior applications. Can fade in exterior exposures. Not recommended for exterior wood substrates.

All surfaces to be painted must be clean, dry and free of all wax, oil, grease, dirt, mildew and any other surface contaminants. Dull glossy surfaces prior to painting. Remove all loose and flaking paint. Feather edges to attain a smooth surface. Fill all holes and cracks with suitable patching compound or caulk.

STEEL - Should be clean and have a slight profile. Although primer isn't necessary, additional rust protection can be achieved through the use of either ALLPRO^® GuardPro™ PDQ™ Primer or GuardPro™ Universal Primer.
ALUMINUM & GALVANIZED METAL - Wipe with solvent and apply vinyl wash primer.
CONCRETE OR MASONRY - Cure at least 30 days prior to painting. Acid etch or sand-sweep poured or precast concrete.
CONCRETE BLOCK - Fill with 1 coat of a Latex Block Filler.
WOOD - interior wood only, self-primed.
PREVIOUSLY PAINTED SURFACES - Wash and rinse all surfaces. Dull glossy surfaces and remove sanding dust. Patch holes and cracks. Spot prime bare areas with appropriate primer.

Spray application recommended. Very small areas may be brushed or rolled.

Airless Spray settings @ 77º:
Tip Size: .013 - .017
Atomization Pressure: 1000-1500 psi

Dries to touch in 15 minutes. May be put into service after 12 hours. Recoatable within two hours or after 18 hours. Sand lightly if after 18 hours.
 

Clean up immediately after use with mineral spirits.

Contains solvents dispose of properly.

Caution

Technical Information

WARNING! FLAMMABLE LIQUID & VAPOR! HARMFUL OR FATAL IF SWALLOWED. VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, NOSE, THROAT AND SKIN IRRITATION. CONTAINS MINERAL SPIRITS, VM&P NAPHTHA.

NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and central nervous system damage. Intentional misuse by deliberately concentrating and inhaling contents may be harmful or fatal.

Keep away from heat, sparks and flame. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application an drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate properly fitted respirator (see Code of Federal Regulations 42 CFR 84) during and after application. Follow respirator manufacturer's directions for respirator use. Close container after each use. Do not get in eyes, on skin or on clothing. Wash thoroughly after handling.

If spilled, contain spilled material and remove with inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

WARNING: This product contains a chemical known to the state of California to cause cancer and birth defects or other reproductive harm.

FIRST AID: in case of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Get medical attention immediately. Wash clothing before reuse. Destroy contaminated shoes. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. If swallowed, do not induce vomiting. Call physician immediately. In case of medical emergency, contact 1-800-424-9300.

USE ONLY WITH ADEQUATE VENTILATION
KEEP OUR OF REACH OF CHILDREN

ATTENTION: The container is hazardous when empty. Empty container retains explosive vapors and flammable residues. All labeled hazard precautions must be observed. Keep away from heat, sparks, and flames. Do not cut, puncture or weld on or near the container. Not rated for pressure, do not apply air or gas pressure. Do not reuse the container for any purpose.

Obtain And Read The Material Safety Data Sheet Before Using.

INTENDED FOR INDUSTRIAL USE ONLY.

Manufactured For:
ALLPRO^® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Ingredients (White 12055)	CAS #
Vinyl Toluenated Alkyd	68458-12-8
V.M. & P Naphtha	8032-32-4
Titanium Dioxide	13463-67-7
Kaolin Clay	1332-58-7
Chlorinated Paraffin	63449-39-8

	HMIS
H	F	R	PP
2	3	0	C