Technical Bulletin
Acrylic Urethane Waterborne Varnish
|
|
Technical Bulletin |
|
|
Acrylic Urethane Waterborne Varnish |
||
|
ALLPRO®
Corporation |
AP2450 - 30511 |
| Description | A
superior clear coating that provides all the durability and wearability
of an alkyd varnish but with much less odor and low VOC. Excellent
clarity, and with proper cure, exhibits outstanding hardness, durability
and abrasion resistance. It is easy to apply and cleans up with soap and
water.
|
| Prominent Features |
|
| Uses | Ideal
for use in residential, commercial offices, institutions and light duty
industrial buildings. Ideal for use on floors, trim, furniture, doors or
cabinets. Not intended for use on exterior surfaces.
|
| Limitations | DO
NOT apply over sanding sealers containing silicone, wax or stearates. Do
not tint. Thinning is not required. If necessary, use ALLPRO ACRYLIC
URETHANE WATERBORNE VARNISH REDUCER up to a maximum of 8 oz. of REDUCER
per gallon. Thinning with ALLPRO REDUCER will alter the VOC of this
product. DO NOT apply coating to wood if wood is obviously moist
(Moisture content above 12% as determined by a moisture meter). DO NOT
APPLY WHEN AIR TEMPERATURE IS BELOW 55ºF.
|
| Surface Preparation | Surface
to be coated must be clean and free of dust, grease, dirt or wax. If wax
is a suspect contaminate, remove with a commercial wax stripper. New
interior wood must be sanded smooth.
|
| Application | This
varnish may be applied by brush, roller or spray. Stir thoroughly before
and occasionally during application. Do not shake. Best rolling results
are achieved with a 1/4" short nap roller. For best brush
application, use a good quality synthetic brush. To prevent streaking,
do not continuously brush or roll over the wet area. Apply coating at up
to 450 square feet per gallon on smooth sealed surfaces. Apply in thin
coats to avoid prolonged milky appearance of the film. Two or three
coats are recommended with light sanding between coats. Allow 4 to 6
hours before sanding. Best results are achieved by first applying
ALLPRO Acrylic Urethane Waterborne Sanding
Sealer.
|
| Clean Up | Clean
up spills and splatters immediately. Clean painting tools with soap and
water. Follow manufacturer's recommendations for thorough spray
equipment maintenance.
|
|
Caution |
Technical Information |
|
Do not take internally. Close container after each use. Keep out of reach of children. WARNING! CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For additional information call (800) 323-0633. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. Manufactured For: |
Packaging: ½ Pints, Quart, Gallon & 5 Gallon Specular Gloss Levels: Gloss, Semi-Gloss, Satin and Eggshell (D.R.E.) Color: Clear Weight per Gallon: 8.62 lbs. per gallon % Solids by Weight: 30.7% % Solids by Volume: 28.5% Viscosity: 60-65 KV Spreading Rate: Per gallon Smooth: 450 sq. ft. Rough: 250 sq. ft. Shelf Life: 2 years Freeze Thaw: Do not freeze Dry Time: At 77°F and 50% RH - To touch: 1 hour To recoat: 2 - 4 hours Flash Point: Over 200°F Odor: Low odor Storage: Indoors, between 40° - 100°F Vehicle: Acrylic Urethane Air Quality Data: VOC - 2.45 lb/gal Analysis: |