Acrylic Urethane Waterborne Clear Wood Varnish Sanding Sealer

Description	ALLPRO ACRYLIC URETHANE WATERBORNE SANDING SEALER is ideal for interior use. It seals completely and provides outstanding penetration into wood surfaces with a minimal amount of grain raising. The clear formulation minimizes potential tannic acid extractive staining which can result when water based finishes are applied over open grained or unseasoned wood.
Prominent Features	» Minimal grain raising » Fast dry » Non-flammable » Does not contain lead, mercury or formaldehyde
Uses	Ideal for use in residential, commercial offices, institutions and light duty industrial buildings. This sealer may be applied to interior wood surfaces such as doors, trim, cabinets, dadoes, furniture, etc. May be used on floors if topcoated with ALLPRO ACRYLIC URETHANE WATERBORNE FINISHES
Limitations	Do not tint. Thinning is not required. If necessary, use ALLPRO ACRYLIC URETHANE WATERBORNE VARNISH REDUCER up to 8 oz. per gallon. Thinning with ALLPRO REDUCER will alter the VOC of this product. DO NOT apply the coating to wood if wood is obviously moist (moisture content above 12% as determined by a moisture meter). DO NOT apply when air or surface temperatures are below 50º F or above 90ºF.
Surface Preparation	Surface to be coated must be clean and free of dust, grease, dirt or wax. NEW OR BARE WOOD: Sand the surface to be sealed until it is smooth and free from flaws. Open grained woods, such as oak, may be filled with paste wood filler if a totally smooth finish is desired. Apply one coat of ALLPRO SEALER. Allow to dry 2 to 4 hours, then sand lightly. Pick sanding dust up with a tack cloth. Apply one or two coats of ALLPRO ACRYLIC WATERBORNE FINISH in the desired sheen. For best sanding results, sand within 48 hours otherwise cured film becomes hard and more difficult to sand. STAINED WOOD: Make sure that the stain is completely dry, then apply a full coat of ALLPRO ACRYLIC WATERBORNE SANDING SEALER. Allow to dry for 2 to 4 hours, then sand lightly and recoat with the ALLPRO clear finish of choice.
Application	Apply by brush, roller or spray. Stir thoroughly before and occasionally during application. Do not shake. Best rolling results are achieved with a 1/4" short nap roller. For best brush application, use a good quality synthetic brush. When brushing or rolling, flow material on with a minimum of strokes, with the wood grain. Do not continuously brush or roll over the wet area. Apply coating at up to 450 square feet per gallon on smooth sealed surfaces.
Clean Up	Clean up spills and spatters immediately. Clean painting tools with soap and water. Follow manufacturer's recommendations for thorough spray equipment maintenance.
Disposal	Contains organic solvents which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your local sanitation department or household hazardous waste coordinator for information concerning possible reuse or disposal of unused solvent-containing adhesives and/or sealants.

Caution

Technical Information

Do not take internally.

WARNING! CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN.

NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For additional information call (800) 323-0633. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: Quart, Gallon & 5 Gallon
Color: Clear
Weight per Gallon: 8.6 lbs per gallon
% Solids by Weight: 31.5%
% Solids by Volume: 29.4%
Viscosity: 58-62 KV
Spreading Rate: Smooth 450 sq. ft. Rough 300 sq. ft.
Shelf Life: 2 years
Freeze Thaw: Do not freeze
Dry Time: At 77ºF and 50% RH
To Touch: 30 minutes
To Recoat: 2 - 4 hours
Flash Point: Over 200ºF
Odor: Low odor
Storage: Indoors, between 40º - 100ºF
Vehicle: Acrylic Urethane
Air Quality Data: VOC - 1.4lb/gal

Analysis:
Acrylic Resin (CAS - Proprietary)
Water (CAS 7732-18-5)
Ethylene Glycol Butyl Ether (CAS 107-21-1)
Propylene Glycol (CAS 57-55-6)
Silicon Dioxide (CAS 112945-52-5)

		Technical Bulletin

		Acrylic Urethane Waterborne Satin Sanding Sealer