Technical Bulletin
Alkyd Quick Drying Sanding Sealer
|
|
Technical Bulletin |
|
|
Alkyd Quick Drying Sanding Sealer |
||
|
ALLPRO®
Corporation |
AP2450 - 30811 |
| Description | A
quick drying, high solid, vinyl toluene formulated sanding sealer. This
sanding sealer is designed for maximum holdout and has excellent sanding
properties. It is an ideal sealer for use on interior wood.
|
| Prominent Features |
|
| Uses | Ideal
for use in residential, commercial offices, institutions and light duty
industrial buildings. Ideal for floors, trim, furniture, doors or
cabinets. Not recommended for use under polyurethane varnish.
|
| Limitations | Do
not tint. Thinning is not advised. THIS PRODUCT CONTAINS ZINC STEARATE
AND SHOULD NOT BE USED AS A SEALER FOR POLYURETHANE VARNISH. DO NOT
apply at temperatures below 55ºF.
|
| Surface Preparation | Surfaces
should be clean, dry and free from dirt, dust and grease. Old paint
films should be removed with a varnish remover. Residue of varnish
remover should be cleaned off with mineral spirits. Old paint may also
be removed by sanding machine but care should be taken to remove all
dust. Stain wood before sealing if desired.
|
| Application | Stir
thoroughly before use. Apply a generous coat with brush, mop or wax
applicator. Apply across the wood grain and then with the wood grain to
ensure complete coverage. For best results, sand lightly with a fine
sand paper before applying finish coat.
|
| Clean Up | Clean
up spills and splatters immediately. Clean painting tools with mineral
spirits. Follow manufacturer’s recommendations for thorough spray
equipment maintenance.
|
| Disposal | Contains
organic solvents which may cause adverse effects to the environment if
disposed of improperly. Place empty containers in normal refuse
for disposal. Contact your local sanitation department or household
hazardous waste coordinator for information concerning possible reuse or
disposal of unused solvent-containing adhesives and/or sealants.
|
|
Caution |
Technical Information |
|
Do not take internally. WARNING! CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For additional information call (800) 323-0633. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. Manufactured For: |
Packaging: Quart, Gallon & 5 Gallon Color: Clear Weight per Gallon: 7.05 lbs. per gallon % Solids by Weight: 38.3% % Solids by Volume: 31.8% Viscosity: 35-45 Sec #4 Ford Cup Spreading Rate: per gallon Smooth: 450 sq. ft. Rough: 350 sq. ft. Shelf Life: 2 years Freeze Thaw: Do not freeze Dry Time: At 77ºF and 50% R.H. To touch: 1 hours To recoat: 4 - 6 hours Flash Point: 50ºF Odor: Mineral Spirits Storage: Indoors, between 40ºF - 100ºF Vehicle: Vinyl Toluene, Linseed Oil, Copolymer Air Quality Data: VOC 4.35 lbs/gal Analysis:
|