Technical Bulletin
A4520 HS Alkyd Zone Marking Paint
|
|
Technical Bulletin |
|
|
A4520 HS Alkyd Zone Marking Paint |
||
|
ALLPRO®
Corporation |
AP2450 - 31801 |
| Description | A
high solids, high build Soya Tall-Oil Alkyd formulation for marking
traffic lines on interior or exterior horizontal surfaces such as
parking lots, warehouses, etc. White, yellow (leaded) and red meet the
requirements of TT-P-115E, type I; while black meets TT-P-110, type I.
|
| Prominent Features |
|
| Uses | Used
for zone marking of traffic lines on interior and exterior horizontal
surfaces.
|
| Limitations | Do
not apply when air or surface temperature is below 40ºF. Do not apply
to extremely hot surfaces. Paint only in dry weather. Do not apply to
fresh asphalt. Not designed as an anti-slip coating.
|
| Surface Preparation | The
surface to be coated must be clean and free of dust, grease, wax, rust,
oil and bleeding stains. New asphalt or any asphaltic seal coat applied
to the surface prior to application of HS Alkyd Zone Marking Paint
should be dry for at least 4 days before this marking paint is used.
Existing traffic lines can be obliterated on asphalt surfaces by coating
with ALLPRO A4521-102 Black HS Alkyd Zone Marking Paint prior to
application of the required color. Allow A4521-102 to dry four (4) hours
before recoating with required color.
|
| Application | May
be applied by brush, roller, spray, hand operated or automatic line
markers. Do not apply when air or surface temperature is below 40ºF. Do
not apply to extremely hot surfaces. Stir contents thoroughly from the
bottom before using. Paint only in dry weather. Thinning is not normally
required. If necessary, thin sparingly with ALLPRO VM&P Naphtha for
spray application or ALLPRO Paint Thinner (Mineral Spirits) for brush or
roller application. Traffic beads may be dropped into this coating while
wet to provide reflectorized markings. If beads are applied, they should
be broadcast into the wet paint at a rate of six (6) pounds per gallon
of paint.
|
| Clean Up | Clean
up immediately after use with ALLPRO Paint Thinner. To avoid spontaneous
combustion, explosion or flash fires, promptly and safely dispose of
used rags, container and unused contents in accordance with local, state
and federal regulations.
|
|
Caution |
Technical Information |
|
A4520-101 White WARNING! FLAMMABLE Contains: Petroleum Distillates and Crystalline Silica. Crystalline Silica may cause cancer. Risk of cancer depends on duration and level of exposure to dust from sanding surfaces or spray mist. Keep away from heat & flame. Do not breathe (dust, vapors or spray mist). To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate properly fitted respirator (see Code of Federal Regulations 42 CFR 84) during and after application. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Avoid contact with skin. Use with adequate ventilation. NOTICE: Reports have associated repeated and prolonged occupational over exposure to solvents with permanent brain & nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. FIRST AID: if you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. KEEP OUT OF REACH OF CHILDREN PROTECT FROM FREEZING ADDITIONAL CAUTION FOR A4520-157 Yellow (leaded) CONTAINS PETROLEUM DISTILLATES, LEAD AND CRYSTALLINE SILICA DRIED FILM OF THIS PAINT MAY BE HARMFUL IF EATEN OR CHEWED Do not apply on toys and other children’s articles, furniture or interior surfaces of any dwelling or facility which may be occupied or used by children. Do not apply on those exterior surfaces of dwelling units, such as windowsills, porches, stairs or railing, to which children may be commonly exposed. Use only with adequate ventilation. Manufactured For:
|
Packaging:
Gallons and five gallons Colors: White, Yellow (leaded), Black, Fire Zone Red Specular (60º) Gloss: 1 - 3% @ 85º Weight Per Gallon: 12.6 lbs. % Solids by Weight: 75.6 % % Solids by Volume: 55.8% Viscosity: 70 - 80 Krebs Units Recommended Film Thickness- Wet: 12.0 - 15.0 mils Dry: 6.7 - 8.4 mils Spreading Rate- 3" line: 400 feet 4" line: 300 feet 5" line: 240 feet 6" line: 200 feet Dry Time- Tack Free: 30 minutes (ASTM D-711) Recoat: 4 hours Full Cure: 10 days Flash Point: 55ºF (TT-P-141, Method 4293) Light Reflectance (White or lightest color): 90% Storage: Indoor, protect from freezing Vehicle: Soya Tall-Oil Alkyd Thinner- Spray: VM&P Naphtha Brush/Roll: Mineral Spirits Clean Up Solvent: Mineral Spirits Federal Specifications - Meets the requirements of - White: TT-P-115E, type I Yellow (Leaded): TT-P-115E, type I Red: TT-P-115E, type I Black: TT-P-110, type I Air Quality Data: Maximum of 360 grams per liter VOC/VOS (3.0 lbs/gal) of coating. Ingredients A4521-101 CAS # |