Professional Waterborne Floor Finish Acrylic Urethane

Description	Two-part waterborne, crystal-clear acrylic polyurethane floor finish designed for interior use in residential, institutional and light commercial wood floor applications. Provides a tough, durable surface.
Prominent Features	» Water White » High solids » Dries dust free in 1-3 hours » Recoatable in 12 hours » Maximum build, adhesion and toughness » Pass the testing requirements for MFMA » Resists abrasion, chipping & peeling » Withstands food spills as well as the affects of most janitorial cleaners
Uses	Formulated for use on wood floors in any residential environment including heavy traffic entrance foyers, children's rooms, living rooms and kitchens. It can also be used in offices, lobbies, waiting rooms, vestibules and similar commercial applications
Limitations	The recommended finishing system is a sealer coat followed by one or two topcoats. Do not use over wood fillers, shellacs, lacquers or any sealer that contains stearates. Do not use steel wool, as any unremoved fibers will rust after waterborne finishes are applied.
Surface Preparation	New Work: Remove all dirt, wax, grease and construction contamination. Sand floors using accepted MFMA or NOFMA methods. CAUTION: Do not use steel wool, as any unremoved fibers will rust after waterborne finishes are applied. Tack with a water dampened towel. Old Work: Remove all dirt, wax, grease and other contamination. If existing finish is in poor condition, it should be completely removed by sanding. Do not use Paint and Varnish Remover. Finishes in good condition should be screened with 100 grit screen. NOTE: Solvent borne finishes should be allowed to cure for a minimum of 30 days before attempting to coat over them with Acrylic Urethane Floor Finish. Over Stains: Can be applied over most stains including ALLPRO® Q.D. Stain. Apply stains in accordance with manufacturer's directions, allowing the recommended drying time. High humidity, low temperature and/or lack of ventilation will extend the drying time of most stains. Make certain stain is thoroughly dried before attempting to coat. Note: Oil stains will normally require a drying interval of 24 - 48 hours. White, pastel or higher solids, VOC compliant oil based stains should be allowed 48 - 72 hours drying time before coating. It is advisable to test a small area for compatibility before proceeding with the entire job. Sealer: On uncoated wood floors, a finishing system consisting of one coat of ALLPRO Professional Waterborne Universal Floor Sealer followed by two coats ALLPRO Acrylic Urethane Floor Finish is recommended. Full directions for applying the ALLPRO Universal Floor Sealer can be found on the label or ALLPRO technical bulletin. Allow sealer to dry for 3 hours before recoating.
Application	Mixing & Activating: Mix material thoroughly to make certain all ingredients are thoroughly dispersed. Pour into a clean working container. While stirring, slowly add 2 ounces of ALLPRO Acrylic Urethane Hardness Enhancer - Floor Finish Part B - per gallon. Continue to stir for a minimum of 30 seconds. Allow mixture to stand for 10 - 15 minutes before using. Once activated, ALLPRO Acrylic Urethane Floor Finish has a pot life of 24 hours. APPLICATION: The surface, material and ambient temperatures should be between 50º F and 95º F for the successful application. Maintain adequate ventilation during the coating and drying process. This helps to speed drying and reduce grain raising. A flat waterborne applicator or synthetic lamb's wool pad is recommended, although a nylon/polyester brush may also be used. Begin by edging the room with a flat pad applicator or nylon/polyester brush. Then, pour a "trail" of material 3 - 4 inches wide, in the direction of the wood grain and 6 - 8 inches from the floor edge. Pull the finish forward with the applicator at a slight angle. Add more product as necessary to maintain the 4" "trail" of material. Make a "U" turn at the end of the room and squeeze out excess material next to the puddle. Continue to spread and move across the room in an "S" pattern. Maintain a wet edge to avoid lapping. Allow the first coat to dry for 1 - 3 hours then screen with a 120-grit screen. Remove all sanding dust by vacuuming and tack the floor lightly with a dampened towel before proceeding with the second coat. If a third coat is necessary, follow the same inter-coat procedure as for the second coat.
Clean Up	Clean tools and equipment immediately after use with soap and water. Rinse well with clean water. Wipe up spills immediately using a damp rag. Dried material is difficult to remove.
Disposal	Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

Caution

Technical Information

CONTAINS: n-Methyl Pyrrolidone and Ethylene Glycol Monobutyl Ether

Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Eye contact may cause corneal injury. May cause skin, nose and or throat irritation. May be harmful if absorbed through skin. May cause blood disorders based on animal tests

Use Only With Adequate Ventilation.

Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH approved) during and after application. Follow respirator manufacturer's directions for respirator use. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Close container after each use. Do not transfer contents to bottles or other unlabeled containers. If the contents of this package is blended with other components before the product is used, any mixture of components will have the hazards of all components. Before opening the packages, read all warning labels and follow all precautions.

KEEP OUT OF REACH OF CHILDREN.

FIRST AID: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention immediately; for skin, wash thoroughly with soap and water. If affected by inhalation of vapor or spray mist, remove to fresh air. If swallowed, get medical attention immediately. If spilled, contain spilled material and remove with inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations .Obtain And Read The Material Safety Data Sheet Before Using

KEEP FROM FREEZING

INTENDED FOR INDUSTRIAL USE ONLY.

Manufactured For:
ALLPRO(r) Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: Gallons
Colors: Clear Gloss, Semi-Gloss & Satin
Specular (60º) Gloss
     Gloss: 85+
     Semi-Gloss: 50-55
     Satin: 30-35
Weight Per Gallon: ~ 8.6 lbs.
% Solids by Weight ~ 29%
% Solids by Volume ~ 25%
Viscosity: 15-25 seconds - #2 Zahn
Recommended Film Thickness:
     Wet: 3 mils
     Dry: 0.9 mils
Spreading Rate: Up to 400 Sq. Ft. per Gallon
Dry Time:
    Tack Free: 1-3 hours
    Recoat: 12 hours
Flash Point: Over 200ºF
Odor: Waterborne Acrylic
Storage: Indoor, away from heat, sparks and flame.
Shelf Life: 3 years
Freeze/Thaw: Keep from freezing
Vehicle: Acrylic Urethane
Air Quality Data: Maximum VOC/VOS
    Gloss: 290 grams per liter (2.4 lbs./gal) of coating
    Semi-Gloss: 300 grams per liter (2.5 lbs./gal)
    Satin: 300 grams per liter (2.5 lbs./gal)
Ingredients (all sheen levels):CAS   #
Glycol Ether PM      107-98-2
Glycol Ether EB       112-34-5
Glycol Ether DPM    34590-64-8
Triethylamine           121-44-8
Acrylic Urethane ** This chemical not subject to reporting requirements of SARA, Title III, Section 3: Title 40 CFR, part 372; or Title 29 CFR, Part 1900.1200.

		Technical Bulletin

		Professional Waterborne Floor Finish Acrylic Urethane - 310 Series