Technical Bulletin
Professional Floor Finish Polyurethane Varnish
|
|
Technical Bulletin |
|
|
Professional Floor Finish Polyurethane Varnish |
||
|
ALLPRO®
Corporation |
AP2450 - 30871 |
| Description | ALLPRO® Professional Floor Finishes are high solids, extremely abrasion resistant polyurethane coatings designed for use on floors and other interior surfaces subject to hard wear. These finishes resist heavy foot traffic, scuffing, detergents, household chemicals, rubber burns and boiling water. |
| Prominent Features |
|
| Uses | Formulated for use on new or properly prepared previously coated floors and other interior wood surfaces. Excellent for use on cabinets, trim and bar tops. |
| Limitations | The recommended finishing system is a sealer coat followed by one or two topcoats. Do not use Professional Floor Finish Polyurethane Varnish over wood fillers, shellacs, lacquers or any sealer that contains stearates. |
| Surface Preparation |
NEW WORK: The surface to be coated must be clean, dry and free of dust, grease, wax and other surface contamination. Sand as necessary, removing all sanding dust with a tack cloth. OLD WORK: Remove old wax by cleaning with a commercial wax stripper or abrading with 000 steel wool that has been saturated with denatured alcohol. While wet, wipe dry with a clean cloth. Repeat if necessary until all wax residue has been removed. NOTE: It is very difficult to remove all traces of old wax. when recoating waxed floors, it is generally preferred to remove all the old finish to bare wood. Glossy finishes must be dulled by sanding prior to the application of the Professional Floor Finish Polyurethane Varnish. Use 120 Grit Sanding Screen. OLD WORK TO BE STAINED: If wood is to be stained, all old paint and varnish must be removed to bare wood. Make sure that surface is free from contamination. Sand smooth and remove all sanding dust using a tack cloth. Make sure the surface is dry and proceed as with new work. STAINING / SEALING: Apply ALLPRO® Q.D. Stain and ALLPRO® Professional Floor Finish Polyurethane Sanding Sealer as directed by the specific ALLPRO® technical bulletins prior to finishing. Top coat with one or two coats of ALLPRO® Professional Floor Finish Polyurethane Varnish of the gloss/sheen of choice. |
| Application | Stir Satin and Semi-gloss gently. Gloss does not require
stirring. DO NOT SHAKE any Professional Finish Polyurethane Varnish or Sanding Sealer.
Apply with a clean, soft natural bristle brush or short-nap woven
or lambswool applicator. May also be applied by spray gun
using the following recommended settings
Apply one or two coats over sealed surface depending on the severity of wear anticipated. Sand lightly between coats using 120 Grit Sanding Screen or buff with 000 Steel Wool. DO NOT APPLY WHEN SURFACE, AMBIENT OR MATERIAL TEMPERATURES ARE BELOW 50°F. Thinning is not recommended. Thinning of this material will result in the VOC level of this product exceeding the limit permitted under EPA AIM Coatings Rule. |
| Clean Up | Clean up immediately after use with Mineral Spirits. |
| Disposal | Contains solvents; dispose of properly.
|
|
Caution |
Technical Information |
WARNING!COMBUSTIBLE Contains Mineral Spirits Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Causes nose and throat irritation.Causes eye and skin burns. Use Only With Adequate Ventilation. Keep away from heat, sparks and flame. VAPORS MAY CAUSE FLASH FIRE. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Do not breathe dust, vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate properly fitted respirator (see NIOSH - Code of Federal Regulations 42 CFR 84) during and after application. Follow respirator manufacturer's directions for respirator use. Do not get in eyes, on skin or on clothing. Close container after each use. Wash thoroughly after handling. Do not transfer contents to bottles or other unlabeled containers. NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and central nervous system damage. Intentional misuse by deliberately concentrating and inhaling contents may be harmful or fatal. FIRST AID: in case of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Get medical attention immediately. Wash clothing before reuse. Destroy contaminated shoes. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. If swallowed, do not induce vomiting. Call physician immediately. KEEP OUT OF REACH OF CHILDREN If spilled, contain spilled material and remove with inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations. ATTENTION: The container is hazardous when empty. Empty container retains explosive and flammable residues. All labeled hazard precautions must be observed. Keep away from heat, sparks, and flames. Do not cut, puncture or weld on or near the container. Not rated for pressure, do not apply air or gas pressure. Do not reuse the container for any purpose. Do not take internally. close container after each use. INTENDED FOR PROFESSIONAL USE ONLY. Manufactured For:
|
Packaging:
Gallons & Five Gallons Ingredients CAS # |