Technical Bulletin
Polyurethane Clear Sanding Sealer
|
|
Technical Bulletin |
|
|
Polyurethane Clear Sanding Sealer |
||
|
ALLPRO® Corporation |
AP2450 - 30721 |
| Description | ALLPRO® POLYURETHANE CLEAR SANDING SEALER™ is a fast driving, easy sanding, hard satin finish that is mar and scuff proof. Ideal for use as a clear sealer coat under polyurethane varnishes. |
| Prominent Features |
|
| Uses | ALLPRO®
POLYURETHANE CLEAR SANDING SEALER is Ideal for use in residential, commercial,
office, institutional and light duty industrial applications. Perfect
for wood floors, trim, paneling, doors, bar-tops or cabinets. Can be used
on bar wood and over most wood stains. |
| Limitations |
Do not tint. Thinning
is not advised. Do not use over paste wood fillers containing stereates.
DO NOT apply at temperatures below 50ºF. Not recommended for exterior
applications. |
| Surface Preparation | Surface
to be coated must be clean, sound, dry and free of rust, grease, oil,
mildew and loose particles prior to application. Old paint films should
be removed with a varnish remover. Residue of varnish remover should be
cleaned off with mineral spirits. Old paint may also be removed by a sanding
machine but care should be taken to remove all dust using an ALLPRO Tack
Cloth. Stain wood before sealing if desired. Open
grained woods may require the use of a stearate-free paste wood filler. |
| Application | Mix
thoroughly. Thinning is not advised. Apply a generous coat with brush,
roller, sprayer, mop or wax applicator. Use a clean natural brush or short
nap, mohair type, roller cover. When spraying, follow equipment manufacturer's
directions regarding top size and spray pressure. Before beginning to
spray, be sure spray equipment is clean and properly functioning. Apply
across the wood grain and then with the wood grain to ensure complete
coverage. Allow a minimum of 8 hours drying time before sanding or top
coating. For best results, sand lightly with fine sandpaper before applying
finish coat. Remove sanding dust with an ALLPRO tack cloth. |
| Clean Up | Clean
up spills and spatters immediately. Clean painting tools with mineral
spirits. Follow manufacturer's recommendations for thorough spray equipment
maintenance. |
| Disposal | Contains
organic solvents which may cause adverse effects to the environment if
disposed of improperly. Place empty containers in normal refuse
for disposal. Contact your local sanitation department or household hazardous
waste coordinator for information concerning possible reuse or disposal
of unused solvent-containing adhesives and/or sealants.
|
|
Caution |
Technical Information |
|
CAUTION COMBUSTABLE: CONTAINS Petroleum Distillates Keep away from heat and flame. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH - Rule 42 CFR 84) or leave the area. Close container after each use. Avoid contact with skin. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY. NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For additional information call (800) 323-0633. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. Manufactured For: Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable. |
Packaging: Quarts & Gallons Color: Clear Weight per Gallon: 7.5 lbs. per gallon % Solids by Weight: 45.6% % Solids by Volume: 36.2% Viscosity: 40 - 50 Sec # 4 Ford Cup Spreading Rate: Smooth Surface: 400 sq. ft. Shelf Life: 2 years Freeze Thaw: Do not freeze Dry Time: At 77ºF and 50% R.H. To touch: 1 hour To recoat: 4 - 6 hours Flash Point: 104ºF Odor: Mineral Spirits Storage: Indoors, between 40º F - 100ºF Vehicle: Polyurethane Alkyd Air Quality Data: VOC 486 g/l per gallon Analysis: |