Premium Polyurethane Varnish

Description	ALLPRO^® POLYURETHANE CLEAR WOOD VARNISHES are tough, durable, clear coatings especially formulated with premium quality polyurethane resins to provide maximum protection on interior wood surfaces. Excellent for use on surfaces which require an aesthetically pleasing finish that is also rugged and wear resistant. ALLPRO^® CLEAR POLYURETHANES withstand abuse from household chemicals, alcohol, water and common solvents as well as heavy foot traffic. Available in Satin and Gloss finishes.
Prominent Features	Maximum protection on all interior wood surfaces including floors and bar tops Excellent clarity Optimum durability & abrasion resistance Flows on easily to produce a beautiful smooth finish Does not contain lead, mercury or formaldehyd
Uses	Ideal for use in residential, commercial offices, institutions and light duty industrial applications. Perfect for use on floors, trim, furniture, paneling, doors, bar-tops or cabinets. Ideal for surfaces that require a wear resistant coating. Can be used on bare wood and over most stains.
Limitations	Do not tint. Thinning is not advised. This varnish should not be used over shellac products, alcohol soluble sealers, lacquer type sealers, lacquers nor over sanding sealers or paste wood fillers containing stearates. Do not apply at temperatures below 50ºF.
Surface Preparation	All surfaces must be clean, sound, dry and free of rust, grease, oil, mildew and loose particles before painting. Sand glossy surfaces for better adhesion. Sand with the grain and remove all dust. If necessary, use a stearate free paste wood filler on open grained wood. When a sealer is required use a stearate free sanding sealer such as ALLPRO POLYURETHANE SANDING SEALER. On old painted or varnished surfaces in poor condition, remove the old finish with a varnish remover; clean all traces of varnish remover with a suitable solvent; patch or seal if necessary and sand lightly. Metal surfaces must be cleaned thoroughly of dirt, dust, lint, grease and oil. Use an ALLPRO Tack Cloth for removing last traces of dust or lint.
Application	Mix thoroughly before using. May be applied with a clean brush or spray. If spraying, be sure spray equipment is properly cleaned and functioning. Flow on full even coat with the grain and avoid excessive brushing. Allow a minimum of 18 hours drying time between coats, and 24 hours for complete dry. Re-coat work must be done within 24 - 48 hours. Sand surface lightly between coats. For maximum protection on all exterior work, apply 3 coats of varnish. Two coats provides adequate protection for interior work. Three coats may be applied for greater depth of luster and higher gloss.
Clean Up	Clean up spills immediately. Clean painting tools with mineral spirits. Follow manufacturer's recommendations for thorough spray equipment maintenance.
Disposal	Contains organic solvents which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your local sanitation department or household hazardous waste coordinator for information concerning possible reuse or disposal of unused solvent-containing adhesives and/or sealants.

Caution

Technical Information

CAUTION COMBUSTABLE: CONTAINS Petroleum Distillates Keep away from heat and flame. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH - Rule 42 CFR 84) or leave the area. Close container after each use. Avoid contact with skin. . USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY

NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For additional information call (800) 323-0633. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging: 1/2 Pints, Quarts & Gallons
Color: Clear
Weight per Gallon: 7.5 lbs per gallon
% Solids by Weight:
     Gloss 50.2%
     Satin 45.8%
% Solids by Volume:
     Gloss 41.5%
     Satin: 36.0%
Viscosity:
     Gloss: 60-70 seconds #4 Ford Cup
     Satin: 40-50 seconds #4 Ford Cup
Spreading Rate: Per Gallon
     Smooth ~ 600 sq. ft.
     Rough ~ 400 sq. ft.
Shelf Life: 2 years
Freeze Thaw: Do not freeze
Dry Time: At 77ºF and 50% R.H.
     To Touch: 4 hours
     To Recoat: 18 hours
Flash Point: 105ºF
Odor: Mineral Spirits
Storage: Indoors, between 40ºF - 100ºF
Vehicle: Polyurethane Alkyd
Air Quality Data:
    Gloss: VOC 3.67 lb/gal
    Satin: VOC 4.05 lb/gal

Analysis:
Alkyd Resin (CAS - Proprietary)
Polyurethane Modified Resin (CAS - Proprietary)
Mineral Spirits (CAS 8052-41-3)
Zirconium Drier (CAS - Proprietary)
Calcium Drier (CAS - Proprietary)

		Technical Bulletin

		Polyurethane Clear Wood Varnish