Technical Bulletin
Fast Dry Polyurethane Interior Varnish
|
|
Technical Bulletin |
|
|
Fast Dry Polyurethane Interior Varnish |
||
|
ALLPRO® Corporation |
AP2450 - 30581 |
| Description |
ALLPRO® Fast Dry Polyurethane
Finish is an economical and durable varnish formulated with polyurethane
resins to provide maximum protection on interior wood surfaces. It is
resistant to abrasion and household chemicals. Available in Satin and
Gloss finish. |
| Prominent Features |
|
| Uses | Ideal
for use in residential and light commercial environments. Perfect for
coating interior floors, trim, furniture, paneling, doors or cabinets. |
| Limitations | Do
not tint. Thinning is not advised. This varnish should not be used over
shellac or alcohol soluble sealers, lacquer sealers or lacquer soluble
sealers. Do not apply at temperatures below 50ºF. |
| Surface Preparation | All
surfaces must be clean, sound, dry and free of rust, grease, oil, mildew
and loose particles before painting. Sand glossy surfaces for better adhesion.
Sand with the grain and remove all dust. If necessary, use a stearate
free paste wood filler on open grained wood. When a sealer is required
use a stearate free sanding sealer such as ALLPRO Fast Dry Polyurethane
Sanding Sealer. On old painted or varnished surfaces in poor condition,
remove the old finish with a varnish remover; clean all traces of varnish
remover with a suitable solvent; patch or seal if necessary and sand lightly.
Metal surfaces must be cleaned thoroughly of dirt, dust, lint, grease
and oil. Use an ALLPRO Tack Cloth for removing last traces of dust or
lint. |
| Application | Mix
thoroughly before using. May be applied with a clean brush or spray. If
spraying, be sure spray equipment is properly cleaned and functioning.
Flow on full even coat with the grain and avoid excessive brushing. Allow
a minimum of 18 hours drying time between coats, and 24 hours for complete
dry. Re-coat work must be done within 24 - 48 hours. Sand surface lightly
between coats. For maximum protection on all exterior work, apply 3 coats
of varnish. Two coats provides adequate protection for interior work.
Three coats may be applied for greater depth of luster and higher gloss. |
| Clean Up | Clean
up spills immediately. Clean painting tools with mineral spirits. Follow
manufacturer's recommendations for thorough spray equipment maintenance. |
| Disposal | Contains
organic solvents which may cause adverse effects to the environment if
disposed of improperly. Place empty containers in normal refuse
for disposal. Contact your local sanitation department or household
hazardous waste coordinator for information concerning possible reuse or
disposal of unused solvent-containing adhesives and/or sealants.
|
|
Caution |
Technical Information |
|
CAUTION COMBUSTABLE: CONTAINS Petroleum Distillates Keep away from heat and flame. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH - Rule 42 CFR 84) or leave the area. Close container after each use. Avoid contact with skin. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY NOTICE: This product contains solvents. Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. This product contains chemicals known to the state of California to cause cancer. For additional information call (800) 323-0633. For additional safety information, refer to the Material Safety Data Sheet for this product. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush eyes immediately with large quantities of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. Manufactured
For: ALLPRO® Corporation Brandon, FL 33511 Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable. |
Packaging: Quarts, Gallon & 5 Gallon Analysis: |