Description	ALLPRO® Concrete Floor Sealer is a water-based acrylic formula designed to protect and seal horizontal concrete and masonry surfaces. It’s an excellent dustproofer and resists oil stains and road salts and chemicals. The low odor formula protects against moisture damage and reduces cracking, pockmarking and spalling. ALLPRO Concrete Floor Sealer has excellent “hot tire” mark release and offers maximum durability in a clear, easy-to-apply, satin finish.
Prominent Features	Water-based acrylic formula Low Odor VOCs <100 g/L Resists Oil, Transmission and Brake Fluid Repels Water, Salt and Chemicals Applies Milky-White, Dries Clear Non-Yellowing Formula Prevents Cracking, Pockmarking and Spalling Reduces Dust
Uses	ALLPRO® Concrete Floor Sealer seals and protects your concrete floor from the damaging effects of water penetration. It penetrates the concrete and forms a protective coating that is excellent for surfaces exposed to light vehicle traffic and the effects of weather and the elements, such as garages, shop floors, warehouse floors, etc.
Limitations	Use on above grade surfaces only. Do not apply if rain is expected within 24 hours or if temperatures fall below 55˚F within 24 hours of application. For increased safety, add a clear non-slip additive before application. Keep from freezing. Do not use on asphalt, clay pavers or other non-porous surfaces. Do not apply to painted or stained concrete, or to concrete less than 30 days old. Do not apply with a sponge roller, sponge brush or hand-pump sprayer. ALLPRO Concrete Floor Sealer is not resistant to all chemicals. Some vehicle tires may contain chemicals that could, under certain circumstances, cause the sealer to debond if vehicle sits for extended periods, or may leave hot tire marks. Most hot tire marks can be removed with a cleaner/degreaser.
Surface Preparation	The critical factor in achieving a lasting finish is surface preparation. Surface must be clean, dry and oil-free. Use a degreaser to remove oil stains. Thoroughly remove all curing compounds and releasing agents. Power washing is recommended. Repair all cracks and surface breaks. Cover windows, doors, etc. prior to application. Use caution when applying on windy days. For new or smooth concrete, acid etching and neutralization are required for proper adhesion. Use a 1:3 solution of muriatic acid and water or a prepared etcher, and follow the manufacturer’s instructions. Newly etched surfaces must be neutralized before sealing.
Application	Read all directions thoroughly. Wear gloves and eye protection. New concrete must have cured for 30 days prior to application. DO NOT SHAKE. ALLPRO® Concete Floor Sealer is ready to use; do not dilute. Note: Sealer appears milky white during application but dries to a clear satin to semi-gloss ﬁnish. Garden Sprayer: lightly spray surface with a fan-tip spray pattern, then backroll to ensure penetration and prevent puddling. Remove overspray immediately with water. Roller: dampen a short-nap (1/4” – 3/8”) roller with water, remove excess, then saturate with sealer. Roll onto surface keeping a wet edge to avoid streaks. Do not allow to puddle, foam or run.
Clean Up/Storage	Clean all tools immediate after use with soap & water. Store unused product in a dry place above 50ºF. Do not use solvent-based cleaners on surface; clean occasionally with a mild soap and water solution.

Caution

Technical Information

KEEP OUT OF REACH OF CHILDREN

For Eye Contact: Flush with water for 15 minutes
For Skin Contact: Prolonged contact may cause irritation. Wash affected area with soap and water.
If Swallowed: Induce vomiting and seek immediate medical attention
Inhalation: If headache or nausea is experienced, remove the individual to fresh air. If symptoms persist, seek medical attention.

For emergency information within the United States call (800) 424-9300; outside the US call (703) 527-3887 (Chemtrec). For additional information, see the Material Safety Data Sheet for this product.

NOTICE: Manufacturer/seller makes no warranty of any kind except that this product is free from defect and is of merchantable quality. Buyer remedy for breach of warranty is limited to replacement of product or refund of purchase price.

Manufactured For:
ALLPRO® Corporation
Brandon, FL 33511

Note: The information, ratings and opinions stated above pertain to the material currently offered and represent the results of tests and calculations believed to be reliable.

Packaging	“F” style white plastic one gallon and black lid 5 gallon buckets
Color	Applies milky white, dries clear
Finish	Satin to Semi-Gloss depending on surface porosity
Paint & Seal	Mix 1 gallon with 1 gallon of acrylic porch & floor enamel. 2 coats recommended.
Weight per gallon	8.5 lbs
% Solids by Volume	20%
Coverage	150-300 sq.ft. per gal., depending on surface porosity (150 for brick, 300 for stone or smooth concrete). Second coat application is 50% greater.
Dry Time at 77ºF, 50% RH	Dry to touch in 1 hour, recoat in 2 hours. Dry to foot traffic in 24 hours, vehicle traffic in 72 hours.
pH	Not specified
Flash Point	>200ºF (>93.3ºC)
Hazardous Materials	Dipropylene Glycol Propyl Ether, CAS #29911-27-1, % by weight – 1-5
Odor	Low
Storage	Between 50-90ºF
Shelf Life	2 years
Freeze/Thaw (ASTM C731)	Do not freeze
Air Quality Data	VOCs <100 g/L

		Technical Bulletin

		ALLPRO Concrete Floor Sealer