MATERIAL SAFETY DATA SHEET
MSDS NAME: EP50XXX ALLPRO 1:1 AMIDE EPOXY PRIMER BASES, WHITES, COLORS
REVISION DATE: 10/01/01 Printed On: 10/08/01 Time: 03:41 PM
SECTION - I - COMPANY AND PRODUCT IDENTIFICATION
Product Name: EP50XXX ALLPRO 1:1 AMIDE EPOXY PRIMER
BASES, WHITES, COLORS
Hazard Rating: Health: 3* Fire: 3 Reactivity: 0 PPI:
Company Identification: INSL-X PRODUCTS CORPORATION
P.O. BOX 694
50 HOLT DR.
STONY POINT NY 10980-0694
Telephone/Fax: (845) 786-5000 (845) 786-5831
Chemtrec (24 Hour): (800) 424-9300
Product Class SOLVENT BASED EPOXY
UN Number 1263
SECTION II - HAZARDOUS INGREDIENTS INFORMATION
Hazardous Ingredients CAS Number WEIGHT%
XYLENE 1330207 11.87
SOLVENT NAPHTA,LIGHT AROMATIC 64742956 6.54
1,2,4-TRIMETHYLBENZENE 95636 4.52
ETHYLBENZENE 100414 1.80
MESITYLENE 108678 1.14
SECTION III - PHYSICAL DATA
Boiling Range: 277.øF - 355.øF (136.11øC - 179.44øC)
Vapor Pressure Range(mmHg): 1.@ 55.øF (12.78øC)
75.@ 68.øF (20.øC)
Evaporation Rate: Faster than n-Butyl Acetate
Vapor Density: Heavier than air
% Volatile Weight 25.82%
% Volatile by Volume 45.91%
Specific Gravity: 1.51957
VOC MAX LBS/GAL & GRMS/LTR 3.32/398.56
SECTION IV - FIRE AND EXPLOSION HAZARD INFORMATION
OSHA Flammability Class: IB
Flash Point: 68.øF (20.øC)
Setaflash
Explosive Range: 0.8%
19.%
FIRE EXTINGUISHING MEDIA: Dry chemical, foam, water fog, carbon
dioxide.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Keep this product away from heat,
sparks, flame, and other sources of ignition. Keep containers closed
when not in use. Closed containers may burst when exposed to extreme
heat or fire. Toxic gases may form when product is exposed to extreme
heat. Product may decompose under fire.
FIRE FIGHTING PROCEDURES: Water may be used to cool and protect
exposed containers. Use self-contained breathing apparatus. Water may
be ineffective in extinguishing a paint fire. Stream of water may
spread the flame. If water is used, fog nozzles are preferable.
HAZARDOUS DECOMPOSITION OR COMBUSTION PRODUCTS: Carbon monoxide,
carbon dioxide, oxides of nitrogen, acrid fumes, ammonia, hydrogen
cyanide, oxygen, peroxides, aldehydes, chlorine, toxic gases, smoke
and soot.
SECTION V - HEALTH HAZARD INFORMATION
INHALATION: If affected, remove to fresh air. If breathing stops,
give artificial respiration. Administer oxygen if available. Get
immediate medical assistance.
SKIN CONTACT: Flush immediately with plenty of water followed by
washing with soap and water. Remove contaminated clothing. Wash
contaminated clothing before reuse. If irritation occurs, consult a
physician.
EYE CONTACT: Flush immediately with large amounts of water,
especially under lids for at least 15 minutes. If irritation or other
effects persist, obtain medical assistance.
INGESTION: If swallowed obtain medical assistance immediately.
PRIMARY ROUTE(S) OF EXPOSURE: Inhalation, skin contact, eye contact,
ingestion, depending on conditions of use. To minimize exposure,
follow recommendations for proper use, handling, ventilation, and
personal protective equipment.
EFFECTS OF OVEREXPOSURE:
INHALATION: Irritation of respiratory tract. Prolonged inhalation may
lead to mucous membrane irritation, fatigue, drowsiness, dizziness and
/or lightheadedness, headache, loss of coordination, nausea, vomiting,
diarrhea, chest pain, blurred vision, coughing, difficulty with
speech, central nervous system depression, intoxication, tightness of
chest, metallic taste, confusion, anesthetic effect or narcosis,
difficulty of breathing, tremors, severe lung irritation, burns, or
damage, liver damage, kidney damage, spleen damage, pulmonary edema,
neurotoxicity, loss of consciousness, respiratory failure, death.
Possible sensitization to respiratory tract. Sanding dust inhalation
may cause lung damage.
SKIN CONTACT: Irritation of skin. Prolonged or repeated exposure can
cause dermatitis, defatting, blistering, severe skin irritation or
burns. Possible sensitization to skin. Skin contact may result in
dermal absorption of component(s) of this product which may cause
central nervous system depression, liver damage, kidney damage.
EYE CONTACT: Irritation of eyes. Prolonged or repeated contact can
cause conjunctivitis, blurred vision, tearing of eyes, redness of
eyes, severe eye irritation or burns, corneal injury.
INGESTION: Ingestion may cause lung inflammation and damage due to
aspiration of material into lungs, mouth and throat irritation, mucous
membrane irritation, fatigue, drowsiness, dizziness and/or
lightheadedness, headache, loss of coordination, nausea, vomiting,
diarrhea, gastro-intestinal disturbances, abdominal pain, central
nervous system depression, intoxication, anesthetic effect or
narcosis, difficulty of breathing, abnormal blood pressure, burns of
the mouth, throat, stomach, liver damage, kidney damage, pulmonary
edema, convulsions, loss of consciousness.
disturbances may indicate excessive eye contact. Dryness, itching,
cracking, burning, redness, and swelling are conditions associated
MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE: None generally
expected when recommendations for proper use, handling, ventilation,
and personal protective equipment are followed.
Contains Ethylbenzene a substance which has been classified as
possibly carcinogenic to humans by IARC.
SECTION VI - STABILITY & REACTIVITY INFORMATION
Stability: This product is stable
Hazardous Polymerization: Hazardous polymerization will not occur
MATERIALS TO AVOID: Oxidizers, acids, bases, reducing agents,
aldehydes, ketones, amines, nitric acid, hydrogen fluoride, caustics,
mineral acids, sodium, nitrates, chlorinated rubber chlorine
triflouride.
CONDITIONS TO AVOID: Elevated temperatures, contact with oxidizing
agent, sparks, open flame, ignition sources.
SECTION VII - ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Eliminate all sources of ignition. Ventilate area. Avoid breathing
vapors. Use appropriate personal protective equipment. Use
self-contained breathing apparatus if necessary. Contain spill and
remove with inert absorbent. Use non-sparking tools. Use proper
containers. Prevent material from entering sewers, natural ways, or
soil.
WASTE DISPOSAL: Dispose in accordance with all applicable local,
county, state, and federal regulations. Do not incinerate closed
containers. If necessary, use only a licensed disposal firm/facility.
SECTION VIII - EXPOSURE CONTROLS/PERSONAL PROTECTION
Occupational Exposure Limits
ACGIH TLV ACGIH TLV-C ACGIH STEL OSHA STEL OSHA PEL
XYLENE
100.00 PPM N/est 150.00 PPM 150.00 PPM 100.00 PPM
SOLVENT NAPHTA,LIGHT AROMATIC
100.00 PPM N/est N/est N/est N/est
1,2,4-TRIMETHYLBENZENE
N/est N/est N/est N/est N/est
ETHYLBENZENE
100.00 PPM N/est 125.00 PPM 125.00 PPM 100.00 PPM
MESITYLENE
N/est N/est N/est N/est N/est
GENERAL PRECAUTIONS TO BE TAKEN IN USE: Use only with adequate
ventilation. Avoid breathing vapor and spray mist. Avoid contact with
skin and eyes. Wash hands after using.
Product may contain substances classified as nuisance particulates
that may be at hazardous levels only during sanding or abrading of the
dried film.
RESPIRATORY PROTECTION: If personal exposure cannot be controlled
below applicable limits by ventilation, wear an appropriate properly
fitted organic vapor/particulate respirator approved by NIOSH/MSHA
(Canadian z94.4).
When sanding or abrading a dried film, wear a dust/mist respirator
approved by NIOSH/MSHA (Canadian z94.4) for dust which may be
generated from this product, the underlying product, or the abrasive.
VENTILATION: Provide dilution ventilation or local exhaust to
maintain the level of vapors and dust below the applicable limits.
Use only non-sparking explosion-proof equipment. Discharge exhaust
only in area away from ignition sources.
PERSONAL PROTECTIVE EQUIPMENT: Splash goggles or safety glasses
with side shields, impervious gloves, impervious clothing, chemical
resistant boots for spill clean up.
HYGIENIC PRACTICES: Wash clothing before reuse. Wash hands before
eating, smoking, or using washroom.
HMIS:
RATINGS: Ratings are only suggested. The contractor/employer has the
ultimate responsibility to evaluate the hazard that this product
represents in the environment in which it is used.
RATING SYSTEM: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe.
*=Chronic effects.
PERSONAL PROTECTIVE EQUIPMENT: This code is left blank. It should be
entered by the contractor/employer who is familiar with the actual
conditions under which this product is ultimately used.
SECTION IX - HANDLING & STORAGE/SPECIAL PRECAUTIONS
HANDLING AND STORAGE: Store in a cool, dry, and well-ventilated area.
Keep away from heat, sparks and open flame. Keep from freezing. Keep
containers tightly closed and upright when not in use. Do not puncture
nor re-use containers. Transfer only to approved containers with
complete and appropriate labeling. Containers should be grounded when
pouring.
OTHER PRECAUTIONS: Use only with adequate ventilation. Use appropriate
respiratory protection. Do not take internally. Keep out of reach of
children. Avoid contact with skin and eyes. Avoid breathing of vapors,
spray mist, or sanding dust. Empty containers may contain hazardous
residues. Wash hands thoroughly after handling, especially before
eating or smoking. If this product is part of a multiple component
system, the resulting mixture may have the hazards of all of its
parts.
SECTION X - ADDITIONAL INFORMATION
SARA TITLE III SECTION 313 (40CFR372):
This product contains a substance(s) that may be subject to the
reporting requirements.
Ingredient Name CAS Number Weight %
XYLENE 1330207 11.87
1,2,4-TRIMETHYLBENZENE 95636 4.52
ETHYLBENZENE 100414 1.80
TSCA:
All Substances in this product are listed on the TSCA inventory or are
not required to be listed on the TSCA inventory:
As of the date of this MSDS, all of the components in this product are
listed (or are otherwise exempt from listing) on the TSCA inventory.
This MSDS complies with OSHA hazard communication standard 29 CFR
1910.1200.
The above information pertains to the products as currently formulated
and is based on the information received from raw material suppliers
and other sources. Insl-x Products Company, Inc. believes, to the best
of its knowledge, information and belief, the information contained
herein to be accurate and reliable as of the date of this material
safety data sheet. However, because the conditions of handling, use,
and storage of these materials are beyond our control, we assume no
responsibility or liability for personal injury or property damage
incurred by the use of these materials and make no warranty, expressed
or implied, regarding the accuracy or reliability of the data or
results obtained from their use. All materials may present unknown
hazards and should be used with caution. the information and
recommendations in this material safety data sheet are offered for the
users' consideration and examination. It is the responsibility of the
user to determine the final suitability of this information and data
and to comply with all applicable international, federal, state, and
local laws and regulations.
CEPA:
All substances in this product are on the Canadian Domestic Substance
List.
SARA TITLE III SECTION 304 CERCLA (40CFR302.4):
This product contains a substance(s) subject to release notification.
Last Page